I think the Jerusalem Declaration on Antisemitism is much better, and allows for legitimate discourse on apartheid, genocide, et cetera. I actually learned about it on Lemmy!

https://jerusalemdeclaration.org/

https://m.youtube.com/watch?v=5YGc4zOqozo

Fortunately it looks like the federal courts don’t allow this any more: https://www.ussc.gov/about/news/press-releases/april-17-2024

But of course the state courts have their own separate rules.

This looks great! I’m super happy with my MK4, and have never had to do anything with it after the initial kit build and re-seating the LCD cable to fix some early screen-blanking issues.

I’ll probably skip this for my own printer since it seems like most (but not all) of the speed up comes from layer height, but $99 is not terrible for anyone who gets value from it. And anyone buying a new printer gets this stuff with no price increase, which is nice and makes the MK4/MK4S even easier to recommend.

I didn’t know how much more dimensionally accurate Prusa’s prints are compared to the competition, but it makes sense now why there are so many calibration models online if that just isn’t the way every printer works. I’ve designed some parts that need an 0.1mm first layer because I’ve never had any failures with that, but I guess if I share the STLs other people might have trouble.

I do think it’s important to be unassailable, because it’d be easy to say “the libs are making misleading claims” and then people not paying lots of attention will think there’s a “both sides” situation going on. I’m sure we all assumed it was literally on display as an exhibit; I was mislead. If you stick to transparent, honest language, the “both sides” stuff falls apart.

The MAGAs are unreachable, but the poorly-informed are out there too, and making them easier to confuse (by actually also spewing misleading-but-technically-true things) is not a good strategy.

Maybe, but that’s still insincere. When truth is on your side you don’t need to use weasel language.

It was sold in the gift shop, not on display. I know it’s not an enormous difference, but let’s try our best to keep the misinformation just on their side.

They definitely don’t know what they’re doing. They featured this one, which is a death trap. It has a disclaimer that it might not be safe above 120V, but it’s absolutely unsafe and a code violation in the US, where we use 120V (and are very litigious). The disclaimer says they’re trying to get it approved which implies they believe it could be and that the design is sound, but fundamentally it cannot meet code in the US for mains voltage use.

Even if the design were sound, there are material requirements, and having seen the quality of prints some people find acceptable, there’s no chance allowing random people online to print their own boxes is safe.

I think they basically run the contests and feature things based on “ooh this is neat” and “this will excite people to use 3d printers”. It’s a marketing thing, and I guess I accept it because I have low expectations of even pretty-good businesses. But if it’s illegal…someone should probably let them know.

I haven’t bought used myself, but based on my own experiences with my printer (MK4; I love it) I don’t think there’s a ton to worry about buying a used quality printer. I would not buy a used low-end printer because the odds are much higher that the seller found it frustrating.

A used Prusa MK3S is probably an excellent choice if a Prusa MK4 kit is out of your budget and a Bambu printer is out of your budget or doesn’t meet your other requirements. The seller probably either realized they don’t actually print often, or upgraded to a MK4 (or XL if they had the budget). While you can upgrade a MK3S to MK4 with Prusa’s upgrade kit, the cost of the kit is so close to just buying an MK4 that it’s not worth doing (and Prusa admits this; they only offer it because of the flak they got for not doing such a kit in the past). The MK3.5 or 3.9 upgrade kits could make sense for some people…but in many cases someone looking to upgrade would likely leave the MK3S untouched and just buy an MK4.

Do you want the printer to be a tool, or a hobby (i.e. you don’t mind fiddling with the printer itself to improve the results, you don’t mind spending more to upgrade components, etc)?

If the printer itself is a hobby you can go cheap, but if you want something reliable you don’t have to mess with or upgrade, I’d suggest getting something as nice as you can afford, maybe a Prusa mini or Bambu A1 mini if you don’t care about open source. Also consider something like a used Prusa Mk3.x.

You’re affecting the hardness of the metals if you’re heating them to glowing point, because you’re heat treating them. The actual consequence is probably minimal, but you could potentially be softening the brass tip which could affect the rate of wear. From skimming a few random online sources, brass is only work-hardened, so if the nozzle was previously hardened, you’re un-hardening it (apparently quenching from high heat only hardens ferrous metals like iron and steel?).

I was expecting Hal

Well, that’s the key… “still being worth getting”. The $100 special Ender 3 at monoprice probably isn’t worth getting for many people because of the frustration involved.

And so in reality the best answer for the question depends on each individual’s time-money tradeoffs.

Thanks for this. I was worried about how some of my filament was wet in a very dry winter, but this explains why it broke in the spots it broke.

Does this apply to printed parts that are under load as well, then, or are they safer because they don’t get bent/unbent the way filament does (assuming you aren’t trying to do a living hinge or other flexing design)?

On the other hand, an experienced driver might forget it’s there since they never use it. Add in a high-stress situation, and you get a problem.

Now imagine you’ve been driving the Tesla for a long time and don’t ever use the manual release because you’re not supposed to so you don’t mess up the window. And then imagine you’re in a high-stress situation. That’s how having an unmarked backup can fail.

Plus, that handle doesn’t even look like a normal handle - I have never see a car where you pull up to exit instead of sideways away from the door.

On the other hand, if you never use the mechanical release and have spent a long time only driving your Tesla, wouldn’t it be possible to forget it’s there while in a high-stress situation?

Lower cost products sometimes have more variability and maybe you got a good one from the factory.

This is an interesting suggestion. The unsupported overhangs at the transitions are part of why I don’t like using gyroid infill; I don’t need my infill to introduce new potential problems in a print. That said, reducing layer height would be disappointing in most cases because I also don’t need my infill to slow the print down (and with some filaments, it’s also pretty visible), so the other suggestions might be more difficult-but better-ideas. It’d be cool to try a patch someone submits.

Did they describe the types of user error that could cause this?